Ceramic coating for cars in Rai
If your car spends eight or nine hours a day in factory parking in Rai, its paint is taking more punishment than you think. A coating gives it a layer to hide behind.
A working day in factory parking
Most cars in Rai arrive at 9 in the morning and leave after dark. In between, they stand in open parking inside the HSIIDC sectors with chimneys, loading docks and service roads all around. By evening there is a fine grey layer on the roof and windscreen, and on a white car you may spot tiny rust-coloured dots.
That layer is industrial fallout: metal particles, soot and chemical dust. In summer heat it bonds to the clear coat and can etch into it. Washing only on weekends means it sits there for days at a time.
What lands on a car in Rai, and what the coating does
A coating changes how each of these behaves on your paint.
| Contaminant | On bare paint | On coated paint |
|---|---|---|
| Metal fallout | Bonds and rusts into orange specks | Sits on top, rinses off with regular washing |
| Factory soot | Leaves a grey film that needs scrubbing | Loosens with a pH-neutral shampoo |
| NH-44 road film and tar | Stains lower panels | Lifts more easily with tar remover |
| Bird droppings | Etch rings into the clear coat in sun | Wipe off cleanly if removed within a day or two |
| Stone chips from trucks | Chip the paint | Still chip the paint, a coating is not impact protection |
Clean first, then coat
Fallout that has already bonded has to come out before any coating goes on, or it gets sealed under the layer. We use an iron remover that turns purple as it dissolves the metal, then clay the paint smooth and machine polish it. The polish is included with every coating.
If the paint has deep etching from months of fallout and droppings, we will show you under lights and quote paint correction separately before going ahead.
Habits that make a coating last in an industrial area
The coating does the heavy lifting, but a few habits decide whether it lasts its full life.
Rinse midweek
A plain water rinse once or twice a week stops fallout sitting on the coating until Sunday.
Never wipe it dry
Dusting a factory-dusty car with a dry cloth scratches even a coated surface.
Wash with two buckets
Use a pH-neutral shampoo, a clean mitt and a separate rinse bucket. Our washing guide has the details.
Park upwind if you can
A spot away from chimneys and loading docks cuts the fallout landing on the car.
Top up every few months
A spray sealant top-up at the studio keeps the beading strong between washes.
Getting the car to us without missing work
Our Sonipat studio is about 12 km from Rai, a short drive down NH-44.
Message us
WhatsApp your car model, a couple of photos and your factory or office location.
Choose drop or pickup
Drop the car on your way in, or ask for pickup from the factory gate on request.
We do the work
7H and 8H are ready the same day. 9H takes a full day and 9H+ needs 1 to 2 days.
Collect after your shift
The car is handed back with a written warranty card and washing instructions.
Company and fleet cars
Units in Rai that run staff cars or pool vehicles can have them coated one or two at a time so no shift is left short. Coated fleet cars are quicker for drivers to keep clean, and they hold their resale value better when the time comes to replace them.
For cars that also run to Delhi daily, adding front PPF takes care of the stone chips that a coating cannot stop. Grade prices are on the price list.
Seeing small orange specks on a white or silver car? That is rusted fallout, and it should come off before the paint is coated.
Questions people ask
Which grade is best for a car parked in HSIIDC Rai all day?
We usually suggest 9H, or 9H+ for a new or dark car. The extra layers give the coating more life under daily fallout and sun.
Can you collect the car from my factory?
Yes, pickup is available on request. Send us the factory address and your shift timing, and we will arrange a time.
How often should a coated car be washed in Rai?
Rinse it once or twice a week and give it a proper shampoo wash every week or two. Fallout should not stay on the coating for long.
Will coating remove the rust specks already on my car?
The coating itself will not. We remove them with iron remover and clay during the preparation, before the coating is applied.
Is it safe to use the factory's pressure washer?
A pressure rinse from a sensible distance is fine. Avoid shared cloths and brushes, which put scratches into the coating.
What happens if the coating starts to lose beading early?
Bring the car in for a check. Often it just needs a decontamination wash and a spray sealant top-up, and the warranty card covers the grade's rated period.
Where the work is done
Sonipat head office
Sai Baba Road, near Devendra Photostat, opp. MRF Tyres, Saipuram, Bhagat Pura, Sonipat, Haryana 131001
+91 70561 03055
+91 70561 66055
Monday to Saturday, 9 AM to 7 PM. Sunday closed.
Want an exact price for your car?
Send the car model and a couple of photos on WhatsApp. We reply with the right option and the price, usually the same day.